SERVICE PROCEDURES

2027 38mm FLOAT NA3 Glidecore Rebuild

Required Parts

  • 803-04-704 Seal Kit: 2027 38 FLOAT NA 3 Glidecore Rebuild, Two Piece Neg Plate

Required Tools

  • 398-00-657 Tooling: Bullet, Sealhead To Shaft, FLOAT NA 2
  • 398-00-681 2002-017 32 Damper-side and ALL 32-34-36-40 Spring-side Removal Tool
  • 398-00-682 2005-017 34-36-40 Damper-side Removal Tool
  • 398-00-706 Tooling: Fork Topcap Socket, 32mm V2, 3/8 Drive
  • 803-01-324 Kit: Tooling: 2019 Clamps, Grip Damper, Body and Shaft
  • 803-04-828 Kit: Tooling: Clamps, 2026, 36 & 36 E-Opt, and 2027 38 Neg Plate

Supplies Needed

  • 10mm Socket
  • 12mm Crow's Foot
  • 12mm Wrench
  • 15mm Socket
  • 2mm Hex Wrench
  • Propane Torch
  • Ratchet
  • Seal Pick
  • Torque Wrench
  • Waste Oil Basin

WARNING: Always wear safety glasses and protective gloves during service to prevent potential injury. Failure to wear protective equipment during service may lead to SERIOUS INJURY OR DEATH.

WARNING: FOX products should be serviced by a trained bicycle service technician, in accordance with FOX specifications. If you have any doubt whether or not you can properly service your FOX product, then DO NOT attempt it. Improperly serviced products can fail, causing the rider to lose control resulting in SERIOUS INJURY OR DEATH.

WARNING: Never attempt to modify air volume spacers or air shaft assemblies, as this can damage your fork causing a loss of control of the bicycle leading to SERIOUS INJURY or DEATH.

WARNING: FOX suspension products contain pressurized nitrogen, air, oil, or all 3. Suspension misuse can cause property damage, SERIOUS INJURY OR DEATH. DO NOT puncture, incinerate or crush any portion of a FOX suspension product. DO NOT attempt to disassemble any portion of a FOX suspension product, unless expressly instructed to do so by the applicable FOX technical documentation, and then ONLY while strictly adhering to all FOX instructions and warnings in that instance.

WARNING: Modification, improper service, or use of aftermarket replacement parts with FOX forks and shocks may cause the product to malfunction, resulting in SERIOUS INJURY OR DEATH. DO NOT modify any part of a fork or shock, including the fork brace (lower leg cross brace), crown, steerer, upper and lower leg tubes, or internal parts, except as instructed herein. Any unauthorized modification may void the warranty, and may cause failure or the fork or shock, resulting in SERIOUS INJURY OR DEATH.

NOTE: To adjust travel on a 2027 38mm fork you must replace the entire Air Shaft Assembly with Inner Air Sleeve. 

Part Description
820-02-749-KIT Service Set: Air Shaft Assy, 2027 38, 160mm, FLOAT NA 3, 1.345" Bore, Short MCU
820-02-750-KIT Service Set: Air Shaft Assy, 2027 38, 170mm, FLOAT NA 3, 1.345" Bore, Short MCU
820-02-751-KIT Service Set: Air Shaft Assy, 2027 38, 180mm, FLOAT NA 3, 1.345" Bore, Short MCU
820-02-629-KIT Service Set: Air Shaft Assy, 2023 Rhythm 38, 180mm, 1.355 Bore
820-02-630-KIT Service Set: Air Shaft Assy, 2023 Rhythm 38, 170mm, 1.355 Bore
820-02-631-KIT Service Set: Air Shaft Assy, 2023 Rhythm 38, 160mm, 1.355 Bore
820-02-632-KIT Service Set: Air Shaft Assy, 2023 Rhythm 38, 150mm, 1.355 Bore
img/help/page3218-04XH/IMG_3498-m.jpg

Step 1

Remove the blue air cap then use a shock pump to slowly release the air pressure while you hold the lower leg arch down.

img/help/page3218-04XH/IMG_3498.jpg
img/help/page3218-04XH/IMG_4006a.jpg
img/help/page3218-04XH/a.jpg


img/help/page3218-04XH/IMG_9958 copy-m.jpg

Step 2

With the fork slightly inverted (the bottom of the fork up past horizontal), remove the black cover, then use a 2mm hex wrench to remove the red rebound knobs. 

img/help/page3218-04XH/IMG_9958 copy.jpg
img/help/page3218-04XH/IMG_9955 copy.jpg


img/help/page3218-04XH/IMG_9961 copy-m.jpg

Step 3

Use a 15mm socket to remove the damper side bottom nut. Make sure to remove and discard the original crushwasher which may be stuck to the bottom nut.

img/help/page3218-04XH/IMG_9961 copy.jpg
img/help/page3218-04XH/IMG_9962 copy.jpg


img/help/page3218-04XH/IMG_9967 copy-m.jpg

Step 4

Use a 10mm socket to unthread and remove the air side bottom nut. Remove and discard the original crushwasher.

img/help/page3218-04XH/IMG_9967 copy.jpg
img/help/page3218-04XH/IMG_9968 copy.jpg


img/help/page3218-04XH/IMG_9969 copy-m.jpg

Step 5

Use Damper Removal Tools 398-00-681 and 398-00-682 to dislodge the shafts from the lowers. Make sure that you have approximately half of the available threads engaged with your tool before striking with your mallet. Remove the damper removal tools, then bring the fork upright over an oil basin to drain. After oil stops draining from the lowers, pull the lowers off of the upper tubes and set them aside.

img/help/page3218-04XH/IMG_9969 copy.jpg
img/help/page3218-04XH/IMG_9970 copy.jpg
img/help/page3218-04XH/IMG_9963 copy.jpg
img/help/page3218-04XH/IMG_9964 copy.jpg
img/help/page3218-04XH/IMG_9943.2 copy.jpg


WARNING: Please verify that all air has been released from the air chamber by pushing down on the Schrader valve core. Failure to release all air pressure before further disassembly may cause parts to eject causing SEVERE INJURY OR DEATH.

img/help/page3218-04XH/IMG_3532-m.jpg

Step 6

With a chamfer-less 6-point 32mm socket (PN: 398-00-705), unthread the topcap assembly completely. Pull straight up to remove the entire topcap assembly from the left side stanchion tube. Some upward force might be needed to overcome the friction of the stock air volume spacers.

img/help/page3218-04XH/IMG_3532.jpg
img/help/page3218-04XH/IMG_3533.jpg


img/help/page3218-04XH/IMG_9931 copy-m.jpg

Step 7

Carefully remove the retaining ring from the bottom of the air side upper tube, taking care not to scratch the upper tube. Thread the damper removal tool (PN: 398-00-681) onto the air shaft and pull out from the upper tube to remove the air shaft assembly.

img/help/page3218-04XH/IMG_9931 copy.jpg
img/help/page3218-04XH/IMG_9932 copy.jpg


img/help/page3218-04XH/IMG_9848 copy (1)-m.jpg

Step 8

Clean the shaft with Isopropyl alcohol then clamp it in your 10mm shaft clamps (PN: 803-01-324). Remove and discard the o-ring from the base stud then carefully apply heat to the shaft at the base stud with a propane torch for 5-10 seconds to break down the Loctite.  

img/help/page3218-04XH/IMG_9848 copy (1).jpg
img/help/page3218-04XH/IMG_2078 copy.jpg
img/help/page3218-04XH/IMG_2079 copy.jpg


img/help/page3218-04XH/IMG_2080 copy-1-m.jpg

Step 9

Unthread the base stud counter-clockwise with a 12mm wrench, then lift up to remove. Remove the remaining o-ring on the base stud and replace with a new greased one from the kit. Lift up on the neg plate to remove it from the shaft.

img/help/page3218-04XH/IMG_2080 copy-1.jpg
img/help/page3218-04XH/IMG_2081 copy.jpg
img/help/page3218-04XH/IMG_9857 copy (1).jpg
img/help/page3218-04XH/IMG_2082 copy.jpg
img/help/page3218-04XH/IMG_2141 copy.jpg


img/help/page3218-04XH/IMG_2085 copy-m.jpg

Step 10

Remove Top Out Bumper and Top Out Spacer.

img/help/page3218-04XH/IMG_2085 copy.jpg


img/help/page3218-04XH/IMG_2086 copy-m.jpg

Step 11

Remove the seal on the outside of the Neg Plate. Clamp Neg Plate using your Neg Plate Clamps (PN:803-04-358)

img/help/page3218-04XH/IMG_2086 copy.jpg
img/help/page3218-04XH/IMG_2160 copy.jpg


img/help/page3218-04XH/IMG_9868 copy (1) copy-m.jpg

Step 12

Using Neg Plate socket ( PN: 398-01-298) unthread Capture Plate (CCW) from Neg. Plate Housing.

img/help/page3218-04XH/IMG_9868 copy (1) copy.jpg
img/help/page3218-04XH/IMG_9869 copy 2.jpg


img/help/page3218-04XH/IMG_2169 copy-m.jpg

Step 13

Remove Neg Plate Seal Carrier and replace the Q-ring with new greased one from the kit.

img/help/page3218-04XH/IMG_2169 copy.jpg
img/help/page3218-04XH/IMG_2166 copy.jpg
img/help/page3218-04XH/IMG_2167 copy.jpg


img/help/page3218-04XH/IMG_2170 copy-m.jpg

Step 14

Replace Compliance O-ring with new greased one from the kit. Reinstall Neg Plate Seal Carrier.

img/help/page3218-04XH/IMG_2170 copy.jpg
img/help/page3218-04XH/IMG_2171 copy.jpg


img/help/page3218-04XH/IMG_9877 copy 2-m.jpg

Step 15

Apply 1-2 drops of red Loctite 263 to the threaded Capture Plate. Using Neg Plate socket ( PN: 398-01-298) thread on (CCW) Capture Plate onto Neg Plate Housing and torque to 50in/lb. Replace the two seals on the outside of the Neg Plate with new ones from the kit and set aside.

img/help/page3218-04XH/IMG_9877 copy 2.jpg
img/help/page3218-04XH/IMG_2174 copy.jpg
img/help/page3218-04XH/IMG_9879 copy 2.jpg


img/help/page3218-04XH/IMG_9886 copy-m.jpg

Step 16

Remove quad ring from Upper Piston. Carefully clamp the wrench flats on the lower piston in a soft jaw vice and unthread Upper Piston counter clockwise with a 28mm socket from Lower Piston.

img/help/page3218-04XH/IMG_9886 copy.jpg
img/help/page3218-04XH/IMG_9901 copy.jpg
img/help/page3218-04XH/IMG_9902.2 copy.jpg
img/help/page3218-04XH/IMG_9903 copy.jpg


img/help/page3218-04XH/IMG_9904 copy-m.jpg

Step 17

Push Piston bolt out from within Lower Piston. Replace Compliance O-ring withing lower Piston and Upper Piston with new ones from the kit.

img/help/page3218-04XH/IMG_9904 copy.jpg
img/help/page3218-04XH/IMG_9905 copy.jpg
img/help/page3218-04XH/IMG_9891 copy.jpg


img/help/page3218-04XH/IMG_9906 copy-m.jpg

Step 18

Reinstall piston bolt and shaft thru lower piston.Install new glide band from the kit on upper piston. Apply 1-2 drops of red Loctite 263 to the threads of the lower piston. and thread on upper piston onto lower piston. Torque to 80in/lb with 28mm socket. Install new quad ring from kit.

 

img/help/page3218-04XH/IMG_9906 copy.jpg
img/help/page3218-04XH/IMG_9907 copy.jpg
img/help/page3218-04XH/IMG_9892 copy.jpg
img/help/page3218-04XH/IMG_9908 copy.jpg
img/help/page3218-04XH/IMG_9909 copy.jpg
img/help/page3218-04XH/IMG_9911 copy.jpg
img/help/page3218-04XH/IMG_9912 copy.jpg


img/help/page3218-04XH/IMG_2142 copy-m.jpg

Step 19

Reinstall Top out spacer and topout bumper.

img/help/page3218-04XH/IMG_2142 copy.jpg
img/help/page3218-04XH/IMG_2144 copy.jpg


img/help/page3218-04XH/IMG_2145 copy-m.jpg

Step 20

Insert the bullet tool (PN: 398-00-657) into the shaft, then coat it with a thin film of Slick Honey. Reinstall the neg plate with it's flat side down. Remove the bullet tool.

img/help/page3218-04XH/IMG_2145 copy.jpg
img/help/page3218-04XH/IMG_2146 copy.jpg
img/help/page3218-04XH/IMG_2147 copy.jpg


img/help/page3218-04XH/IMG_2148 copy-m.jpg

Step 21

Apply 1-2 drops of red Loctite 262 to the threads inside the shaft, taking caution not to get Loctite in the area of the shaft where the base stud o-ring will seat. Insert the base stud and thread it in clockwise, tightening to 50 in-lb (5.7 Nm) torque with a 12mm crow's foot.

img/help/page3218-04XH/IMG_2148 copy.jpg
img/help/page3218-04XH/IMG_2149 copy.jpg
img/help/page3218-04XH/IMG_2150 copy.jpg


img/help/page3218-04XH/IMG_2151 copy-m.jpg

Step 22

Install a new greased o-ring from the kit onto the base stud.

img/help/page3218-04XH/IMG_2151 copy.jpg
img/help/page3218-04XH/IMG_2152 copy.jpg


img/help/page3218-04XH/IMG_2153 copy-m.jpg

Step 23

Apply a thin film of Slick Honey to the inside of the upper tube. Apply a thick film of Slick Honey to the air shaft assembly in the areas of the piston, neg plate, and shaft above the neg plate. 

img/help/page3218-04XH/IMG_2153 copy.jpg
img/help/page3218-04XH/IMG_2154 copy.jpg


img/help/page3218-04XH/IMG_2156 copy-m.jpg

Step 24

Insert the air shaft assembly into the end of the upper tube. Push the air shaft assembly into the upper tube far enough to allow you to start the neg plate into the upper tube. Push the shaft into the upper tube to pull the neg plate into its installed position.

img/help/page3218-04XH/IMG_2156 copy.jpg
img/help/page3218-04XH/IMG_2157 copy.jpg


img/help/page3218-04XH/IMG_2158 copy-m.jpg

Step 25

Replace the retaining ring making sure it is fully seated in its groove by pulling on the air shaft.

img/help/page3218-04XH/IMG_2158 copy.jpg
img/help/page3218-04XH/IMG_2159 copy.jpg


Step 26

Inject 3cc of FOX 20wt. Gold oil into the main air chamber through the top of the upper tube. Reinstall the topcap into the fork crown and tighten clockwise to 220 in-lb (24.8 Nm) torque with your 6-point chamfer-less 26mm socket.



Step 27

Add air pressure to your desired setting using a FOX high pressure pump. See the Setting Fork Air Pressure section for more information. Reinstall the blue air cap.



img/help/page3218-04XH/IMG_9943 copy-m.jpg

Step 28

Install the Lower Leg Assembly onto the upper tubes. Inject the approprate amount of bath oil into each leg through the bottom hole. Please reference the bath oil chart for your fork

img/help/page3218-04XH/IMG_9943 copy.jpg
img/help/page3218-04XH/IMG_9946 copy.jpg
img/help/page3218-04XH/IMG_9947 copy.jpg


img/help/page3218-04XH/IMG_9950 copy-m.jpg

Step 29

Install a new crushwasher on each side followed by the appropriate bottom nut. Torque air spring bottom nut to 50in-lb (5.7 Nm) and damper bottom nut to 110in-lb (12.4Nm) for Grip X and Grip X2 dampers. 150in-lb (16.9Nm) for Grip damper.

img/help/page3218-04XH/IMG_9950 copy.jpg
img/help/page3218-04XH/IMG_9951 copy.jpg
img/help/page3218-04XH/IMG_9952 copy.jpg
img/help/page3218-04XH/IMG_9953 copy.jpg


img/help/page3218-04XH/IMG_9959 copy-m.jpg

Step 30

Use a 2mm hex wrench to install the red rebound knob. Make sure that the set screw lines up with the depression in the rebound adjuster shaft. Clean the exterior of your fork.Replace the black rebound knob cover and clean the exterior of your fork.

img/help/page3218-04XH/IMG_9959 copy.jpg
img/help/page3218-04XH/IMG_9956.2 copy.jpg